Snobbish Pocketed Zip Up Turtleneck Puffer Jacket | Black / S 100100697111485

How to measure

To capture accurate product measurements for the Snobbish Pocketed Zip Up Turtleneck Puffer Jacket, measure the garment laid flat on a hard surface with a soft tape measure. Record values in both centimeters and inches when possible. For circumference measurements, measure flat and multiply by 2.

1. Chest / Bust: Zip the jacket closed and lay flat. Measure straight across the front about 1–2 cm (¼–¾ in) below the armholes from seam to seam. Double that number to get the full chest circumference.
2. Shoulder width: Measure straight across the back from shoulder seam to shoulder seam.
3. Sleeve length: Measure from the top of the shoulder seam down to the end of the cuff. If you prefer the full-arm length, measure from the center back of the neck over the shoulder to the wrist.
4. Center back length: Measure from the base of the collar at the center back straight down to the hem.
5. Hem width: Measure straight across the bottom hem and double to get the circumference.
6. Turtleneck height: Measure from the neckline seam to the top edge of the turtleneck collar.
7. Pocket depth: Measure from the pocket opening to the bottom inside the pocket.

Measuring tips: Smooth the jacket flat without stretching. If seams are asymmetric, measure both sides and use the larger figure. When listing product measurements, note whether measurements were taken with the jacket zipped or unzipped and whether any trim or ribbing was stretched slightly during measurement.

Materials & construction

The exact materials can vary by production batch—always confirm with the sewn-in care label or product technical sheet. Typical construction for a pocketed zip-up turtleneck puffer includes:

• Shell (outer fabric): Usually polyester or nylon with a durable water-repellent (DWR) finish for light rain and wind resistance. These fabrics are chosen for abrasion resistance and color retention.
• Insulation (fill): Either natural down (a down/feather blend with a specified down percentage and fill power) or synthetic polyester fiberfill. Down provides high warmth-to-weight and compressibility; synthetic fill stays insulating when wet and is easier to care for.
• Lining: Typically a smooth polyester lining for comfort and quick moisture transport.
• Trims and hardware: Zip closure (often YKK or molded plastic), knit collar/cuff trims (polyester/elastane blend), reinforced pocket bags, and taped or bar-tacked stress points.
• Finishes: Some jackets include a DWR coating or water-repellent treatment on the shell that can be refreshed with a reproofing product over time.

How to confirm exact materials: Check the inner care label or the product specification on the product page for percentages (e.g., "100% polyester shell," "80/20 down/feathers," or "100% polyester fill").

Model & fit

Example model reference: Model height: 176 cm (5'9.5") • Bust: 84 cm • Waist: 63 cm • Hips: 91 cm • Wearing size: S. (Replace with actual model details when available.)

Fit notes: This puffer is designed as a slightly relaxed, hip-length jacket with a zip-up turtleneck for added neck warmth. It accommodates a midweight sweater underneath. If you prefer a slimmer silhouette or intend heavy layering, consider sizing accordingly. Always compare your body or favorite-jacket flat measurements to the product measurements above for the best fit.

Care Guide (to keep it lovely longer)

Follow the garment care label first. Below are general recommendations to preserve appearance, insulation performance and finishes.

• Pre-wash: Empty pockets, close zippers and fasten any snaps/Velcro, remove detachable parts, and turn the jacket inside out.
• Machine wash (synthetic fill): Cold water, gentle cycle, mild detergent. Avoid bleach and fabric softeners. Tumble dry low or air dry; use dryer balls to help loft recovery.
• Machine wash (down fill): Use a front-loading washer if possible and a down-specific cleaner. Gentle cold cycle. Tumble dry low with clean tennis balls or dryer balls to break clumps and restore loft; ensure complete dryness to prevent odors and mildew.
• Spot cleaning: For small stains, use a damp cloth and mild detergent. For grease, apply a small amount of dish soap, rinse gently, then launder.
• Do not iron: Avoid ironing the shell. High heat can melt synthetic shells and damage finishes.
• Dry cleaning: Only if the care label permits; many puffers are designed to be machine washable and unnecessary dry cleaning can strip finishes.
• Reproofing: If water stops beading on the shell, refresh the DWR with a spray-on or wash-in reproofing product made for technical fabrics.
• Storage: Store on a wide hanger or loosely folded in a breathable bag; avoid long-term compression (vacuum bags) which reduces loft and insulation performance.
• Small repairs: Use fabric repair tape or an interior patch for small snags/tears. Lubricate or replace zipper sliders as needed.

Quick checklist for best results: close zippers before wash, use mild detergent, dry thoroughly, and reproof shell when needed.

Style tips

• Everyday casual: Pair the turtleneck puffer with high-rise jeans, a slim knit top, and ankle boots. Add a beanie and a crossbody bag for effortless city wear.
• Sporty & travel-ready: Layer over a base layer and leggings with trainers. The zip-up turtleneck provides extra wind protection on travel days.
• Smart-casual: Wear over a thin merino or button-down with tailored trousers and chelsea boots to balance the puffer’s volume for a polished look.
• Proportion & color: Because puffers add bulk, balance with streamlined bottoms (skinny jeans, slim joggers, pencil skirts). Use neutral basics with a bold jacket color to make the jacket the focal point.
• Accessories: Structured totes or small crossbody bags work well across the chest; chunky scarves add warmth but keep the rest of the outfit slim to avoid extra bulk.

Note: For exact fabric percentages, fill type, fill weight or precise model measurements, refer to the product technical sheet or the sewn-in care/contents label on the jacket.