Shiny Leopard Hooded Coat with Pockets | Leopard / S 100100351900552

How to measure this coat

All measurements are typically taken with the coat laid flat on a table, smoothed but not stretched. Record measurements in centimetres (cm) and inches (in). To convert: 1 in = 2.54 cm.

1. Product (flat) measurements — what to take
   • Chest / Bust (pit to pit): measure straight across from underarm seam to underarm seam, then multiply by 2 to get full circumference.
   • Shoulder width: measure from shoulder seam to shoulder seam across the back.
   • Sleeve length: measure from shoulder seam to sleeve end (cuff).
   • Center back length: measure from the centre back neck seam (where collar joins) straight down to the hem.
   • Hem width: measure across the bottom hem from side to side (multiply by 2 for circumference).
   • Hood depth: measure from the base seam at the back of the hood (where it attaches to the collar) over the top to the front edge.
   • Pocket opening width: measure the horizontal opening of each pocket. Also measure pocket depth from the opening straight down to the bottom seam inside the pocket.
   • Sleeve opening (cuff) width: measure cuff flat across (multiply by 2 for circumference).
2. Body measurements — how a customer should measure themselves
   • Bust/Chest: measure around the fullest part of your chest, keeping the tape parallel to the floor.
   • Waist: measure around the narrowest point of the waist (natural waistline).
   • Hips: measure around the fullest point of the hips.
   • Arm length: with a slightly bent elbow, measure from the shoulder tip down to the wrist.
3. Fit advice & tips
   • If you plan to layer heavy knits underneath, allow extra ease — about 4–8 cm (1.5–3 in) more at the chest and shoulders than your body measurement.
   • Compare the product flat measurements (above) to a favourite coat that fits you to choose the best size.
   • Record both cm and in on the product page so international customers can compare easily.

Materials (typical for this style)

Below are common materials and properties for a shiny, leopard-patterned hooded coat with pockets. Confirm exact composition on the garment label or product spec sheet.

• Outer shell: 100% polyester with a glossy PU or laminated finish — gives the shiny look and is usually splash-resistant and easy to wipe clean.
• Lining: 100% polyester taffeta or satin — smooth for easy layering.
• Insulation (if present): 100% polyester fill — lightweight warmth without bulk.
• Hood/faux-fur trim (if applicable): synthetic fibres (acrylic/modacrylic or polyester) — animal-friendly and soft.
• Hardware: metal or coated plastic zippers, snaps or toggles, chosen to match or complement the shiny finish.

Notes: PU coatings and laminated finishes create the shine but can be sensitive to high heat and harsh solvents. Faux fur needs different care than the shell, so check whether trims are detachable before laundering.

Model information (use as a template)

Replace the placeholder values below with the actual model details used in your product photos.

• Model height: 5'9" (175 cm)
• Model measurements (example): Bust 33" / 84 cm • Waist 24" / 61 cm • Hips 35" / 89 cm
• Wearing size in photos: S (Small)
• Fit shown: relaxed / slightly oversized — ideal for layering. Check product measurements to choose your best fit.

Tip: place the real model information here so customers can judge fit against their own measurements.

Care guide — keep it lovely longer

Follow these care tips to maintain the shiny finish, preserve faux trims, and extend the life of the coat.

• Always check the care label first. The label will tell you whether the coat should be hand-washed, machine-washed, or professionally cleaned.
• Spot clean for small marks: use a soft cloth dampened with lukewarm water and a mild detergent. Wipe gently and air dry.
• Hand wash or gentle machine wash: if allowed, turn the coat inside out, zip up closures, use a laundry bag, cold water, and a gentle cycle with mild detergent.
• Do not bleach or use harsh solvents. They can damage the shiny coating and printed pattern.
• Do not tumble dry. Hang to dry away from direct sunlight or heat sources. Do not wring or twist.
• Ironing: avoid direct ironing on shiny/coated surfaces. If needed, iron on the lowest setting on the reverse side with a press cloth, or use low steam at a safe distance.
• Faux fur trims: detach before washing if possible. Gently brush when dry; do not expose to heat.
• Professional cleaning: for heavy soiling or when in doubt, use a dry cleaner experienced with coated fabrics and faux fur.
• Storage: hang the coat on a wide or padded hanger to keep shape, store in a breathable garment bag (avoid plastic), and keep it clean before long-term storage to prevent staining or moth damage.
• Avoid friction and oils: sharp edges, bag straps, and oily perfumes can wear down the coating. Wipe spills immediately.

Style tips — how to wear the shiny leopard hooded coat

• Casual daytime: white tee or knit, slim jeans and white sneakers. Let the coat be the statement piece.
• Street / athleisure: hoodie or sweatshirt layered underneath, leather-look leggings and chunky boots or trainers for an edgy look.
• Smart-casual / evening: a black slip dress or a simple black knit dress with ankle boots and minimalist gold jewelry — the coat adds instant drama without extra effort.
• Belt it: use a wide belt at the waist to convert the boxy silhouette into a tailored shape for a more feminine look.
• Mixing prints: pair with small-scale patterns or tonal stripes if you want pattern play — keep colors in the same palette to avoid clash.
• Colour pairing: neutrals (black, white, beige) are a safe match; deep jewel tones (burgundy, forest green) create a sophisticated contrast.
• Accessories: matte leather bags and understated metal jewellery balance the shiny finish — avoid reflective accessories that compete with the coat's sheen.
• Travel-friendly: the wipe-clean shell makes this coat a practical, stylish choice for city breaks — pair with a crossbody bag and comfortable boots.